LAN switching Totally Explained

Everything about Lan Switching totally explained

ť This article addresses packet switching in computer networks.

LAN switching is a form of packet switching used in local area networks. Switching technologies are crucial to network design, as they allow traffic to be sent only where it's needed in most cases, using fast, hardware-based methods.

History

Prices on OSI model layer 2 switching equipment dropped dramatically around the turn of the 21st century, making it easier to justify the cost of buying switches for an entire local area network. This doesn't mean that every business can afford switch ports for all users, but it does allow for a cost-effective upgrade method.

Layer 2 switching

Layer 2 switching is hardware based, which means it uses the media access control address (MAC address) from the host's network interface cards (NICs) to decide where to forward frames. Switches use application-specific integrated circuits (ASICs) to build and maintain filter tables (also known as MAC address tables). One way to think of a layer 2 switch is as a multiport bridge.
Layer 2 switching provides the following

Hardware-based bridging (MAC)
Wire speed
High speed
Low latency
Low cost

Layer 2 switching is highly efficient because there's no modification to the data packet, only to the frame encapsulation of the packet, and only when the data packet is passing through dissimilar media (such as from Ethernet to FDDI). Layer 2 switching is used for workgroup connectivity and network segmentation (breaking up collision domains). This allows a flatter network design with more network segments than traditional 10BaseT shared networks. Layer 2 switching has helped develop new components in the network infrastructure

Server farms — Servers are no longer distributed to physical locations because virtual LANs can be created to create broadcast domains in a switched internetwork. This means that all servers can be placed in a central location, yet a certain server can still be part of a workgroup in a remote branch, for example.

Intranets — Allows organization-wide client/server communications based on a Web technology. These new technologies are allowing more data to flow off of local subnets and onto a routed network, where a router's performance can become the bottleneck.

Limitations

Layer 2 switches have the same limitations as bridge networks. Remember that bridges are good if a network is designed by the 80/20 rule: users spend 80 percent of their time on their local segment.
Bridged networks break up collision domains, but the network remains one large broadcast domain. Similarly, layer 2 switches (bridges) can't break up broadcast domains, which can cause performance issues and limits the size of your network. Broadcast and multicasts, along with the slow convergence of spanning tree, can cause major problems as the network grows. Because of these problems, layer 2 switches can't completely replace routers in the internetwork.

Layer 3 switching

The only difference between a layer 3 switch and a router is the way the administrator creates the physical implementation. Also, traditional routers use microprocessors to make forwarding decisions, and the switch performs only hardware-based packet switching. However, some traditional routers can have other hardware functions as well in some of the higher-end models. Layer 3 switches can be placed anywhere in the network because they handle high-performance LAN traffic and can cost-effectively replace routers. Layer 3 switching is all hardware-based packet forwarding, and all packet forwarding is handled by hardware ASICs. Layer 3 switches really are no different functionally than a traditional router and perform the same functions, which are listed here

Determine paths based on logical addressing

Run layer 3 checksums (on header only)

Use Time to Live (TTL)

Process and responds to any option information

Can update Simple Network Management Protocol (SNMP) managers with Management Information Base (MIB) information

Provide Security The benefits of layer 3 switching include the following

Hardware-based packet forwarding

High-performance packet switching

High-speed scalability

Low latency

Lower per-port cost

Flow accounting

Security

Quality of service (QoS)

Layer 4 switching

Layer 4 switching is considered a hardware-based layer 3 switching technology that can also consider the application used (for example, Telnet or FTP).
   Layer 4 switching provides additional routing above layer 3 by using the port numbers found in the Transport layer header to make routing decisions.
   These port numbers are found in Request for Comments (RFC) 1700 and reference the upper-layer protocol, program, or application.
   Layer 4 information has been used to help make routing decisions for quite a while. For example, extended access lists can filter packets based on layer 4 port numbers. Another example is accounting information gathered by NetFlow switching in Cisco's higher-end routers.
   The largest benefit of layer 4 switching is that the network administrator can configure a layer 4 switch to prioritize data traffic by application, which means a QoS can be defined for each user.
   For example, a number of users can be defined as a Video group and be assigned more priority, or band-width, based on the need for video conferencing.
   However, because users can be part of many groups and run many applications, the layer 4 switches must be able to provide a huge filter table or response time would suffer. This filter table must be much larger than any layer 2 or 3 switch. A layer 2 switch might have a filter table only as large as the number of users connected to the network and may be even less if some hubs are used within the switched fabric. However, a layer 4 switch might have five or six entries for each and every device connected to the network. If the layer 4 switch doesn't have a filter table that includes all the information, the switch won't be able to produce wire-speed results.

Multi-layer switching (MLS)

Multi-layer switching combines layer 2, 3, and 4 switching technologies and provides high-speed scalability with low latency. It accomplishes this high combination of high-speed scalability with low latency by using huge filter tables based on the criteria designed by the network administrator.
Multi-layer switching can move traffic at wire speed and also provide layer 3 routing, which can remove the bottleneck from the network routers. This technology is based on the idea of route once, switch many.
Multi-layer switching can make routing/switching decisions based on the following

MAC source/destination address in a Data Link frame

IP source/destination address in the Network layer header

Protocol field in the Network layer header

Port source/destination numbers in the Transport layer header There is no performance difference between a layer 3 and a layer 4 switch because the routing/switching is all hardware based.

Further Information

Get more info on 'Lan Switching'.

External Link Exchanges

Do you know how hard it is to get a link from a large encyclopaedia? Well we're different and will prove it. To get a link from us just add the following HTML to your site on a relevant page:

<a href="http://lan_switching.totallyexplained.com">LAN switching Totally Explained</a>

Then simply click through this link from your web page. Our crawlers will verify your link, extract the title of your web page and instantly add a link back to it. If you like you can remove the words Totally Explained and embed the link in article text.
As long as your link remains in place, we'll keep our link to you right here. Please play fair - our crawlers are watching. Your site must be closely related to this one's topic. Any kind of spamming, dubious practises or removing the link will result in your link from us being dropped and, potentially, your whole site being banned.